Difference between revisions of "RPi infrasound logger"

From DFN Wiki
Jump to: navigation, search
(Data retrieval)
 
(2 intermediate revisions by the same user not shown)
Line 1: Line 1:
 +
Also see instructions from Masa-yuki-san.
 +
 
= Power =
 
= Power =
 
Powered using 12V 100Ah+ [[temporary battery with sunshield|temporary battery with sunshield]].
 
Powered using 12V 100Ah+ [[temporary battery with sunshield|temporary battery with sunshield]].
Line 5: Line 7:
 
Location of the instrument is NOT logged by the instrument itself.
 
Location of the instrument is NOT logged by the instrument itself.
 
Do at least [[handheld GPS position logging|handheld GPS unit logging]].
 
Do at least [[handheld GPS position logging|handheld GPS unit logging]].
AND if possible [[RTK|RTK relative positioning]] between the instruments at the same site.
+
AND relative position with respect to 3 nearby sites using tape measurer.
  
 
= Set up =
 
= Set up =
Line 21: Line 23:
 
* "logging"
 
* "logging"
  
When you leave the screen should be on "logging".
+
When you leave the screen should still be on "logging".
  
  
Line 28: Line 30:
  
 
= Data retrieval =
 
= Data retrieval =
 +
== Option 1: ssh ==
 +
* connect ethernet cable between RPi and laptop
 +
* set laptop IP to some thing in the same range
 +
* "mkdir -p ~/Hayabusa_collected_data/infrasound/instrument_ID"
 +
* "rsync -a pi@192.168.1.56:~/data/ ~/Hayabusa_collected_data/infrasound/instrument_ID"
 +
* you can use the opportunity to be connected to safely turn it off (if packing up at the same time): "ssh pi@192.168.1.56 sudo reboot", wait a couple of seconds, and then unplug.
 +
 +
== Option 2: direct card read ==
 
* Take micro SD card out, plug it in a good brand card reader directly (avoid using micro SD -> SD adapter)
 
* Take micro SD card out, plug it in a good brand card reader directly (avoid using micro SD -> SD adapter)
 
* "lsblk"
 
* "lsblk"
Line 35: Line 45:
 
* "umount ~/rpi_data_mount"
 
* "umount ~/rpi_data_mount"
 
* Put micro SD card back into RPi (do not erase data)
 
* Put micro SD card back into RPi (do not erase data)
 
* put micro SD
 

Latest revision as of 11:54, 2 December 2020

Also see instructions from Masa-yuki-san.

Power

Powered using 12V 100Ah+ temporary battery with sunshield.

Localisation

Location of the instrument is NOT logged by the instrument itself. Do at least handheld GPS unit logging. AND relative position with respect to 3 nearby sites using tape measurer.

Set up

  • Remove transport padding from inside the box.
  • Visually check cable connexions
  • Feed 2.1 mm jack to inside the box.
  • Place box under sunshield (South of the battery)

Plug in / Turn on

Plug in instrument box via 2.1 mm 12V jack to cigarette lighter plug.

Inside the box, screen will display its status:

  • "GPS OK"
  • "starting logging"
  • "logging"

When you leave the screen should still be on "logging".


Turn off

Simply unplug the power as there is no power down button (there is a small risk of SD card corruption).

Data retrieval

Option 1: ssh

  • connect ethernet cable between RPi and laptop
  • set laptop IP to some thing in the same range
  • "mkdir -p ~/Hayabusa_collected_data/infrasound/instrument_ID"
  • "rsync -a pi@192.168.1.56:~/data/ ~/Hayabusa_collected_data/infrasound/instrument_ID"
  • you can use the opportunity to be connected to safely turn it off (if packing up at the same time): "ssh pi@192.168.1.56 sudo reboot", wait a couple of seconds, and then unplug.

Option 2: direct card read

  • Take micro SD card out, plug it in a good brand card reader directly (avoid using micro SD -> SD adapter)
  • "lsblk"
  • "mkdir -p ~/Hayabusa_collected_data/infrasound/instrument_ID"
  • "sudo mount /dev/sdX1" ~/rpi_data_mount
  • "rsync -a ~/rpi_data_mount/home/pi/data/ ~/Hayabusa_collected_data/infrasound/instrument_ID"
  • "umount ~/rpi_data_mount"
  • Put micro SD card back into RPi (do not erase data)