RS&BOOM

From DFN Wiki
Revision as of 10:32, 13 November 2020 by Es1208 (talk | contribs)
Jump to: navigation, search

Raspberry Shake

Setting up

Plug in usb connector (gives rfemale USB port). Plug in GPS unit

Plug Ethernet cable in and connect other end with Ethernet jack in wall or Wifi router

Plug USB power cable in (be gentle with the connector) and plug into 12V splitter USB port.

Blue LED should light up when powered on.

Unit needs to be well coupled to the ground. Either place on a solid rock surface, or scrape off any loose material to place on the firmest ground possible.

3D units must be aligned to North.

Use screw legs and bubble level to ensure unit is flat.

Connecting

Connect to the pi in order to check date and that data are being collected. Plug ethernet cable into Pi and other end into wifi router/hub

connect to that wifi via laptop

Open browser on desktop computer (or tablet, phone) and navigate to http://rs.local (if this does not work, find IP address of raspberry shake (for Windows 10 cmd: arp –a) and type in your browser http://???.?.??.???) . Raspberry Shake can be configured by choosing Settings icon

In a terminal, ssh to myshake@rs.local


Default username and password: username: myshake, password: shakeme

checking the time

In terminal $date

In browser, should be on home page as "System Time"

Note time should be in UTC

If needed, setting time to laptop time $ ssh myshake@rs.local "sudo date --set \"$(date)\""

check connection of GPS: $ ntpq -p

Checking status

System Status should be RUNNING. May take a few moments in BOOTING.

Ensure that the data-producer is ON



checking out the data

Helicorder plot (last 12h of data, updates every 2 min) can be seen on http://rs.local/heli

Program ‘swarm’ (available on Linux, MAC, Windows) can be downloaded on webpage to visualize seismic data from Raspberry Shake (http://rs.local >> Actions icon (green icon on bottom) >> Downloads >> Swarm), for Windows: open swarm_console.bat, Linux+MAC: sh swarm.sh (note, you will need to have openjdk-8-jre installed).

Data from Raspberry shake is in folder myShake – Networks – AM, RS Community folder shows data from raspberry shake community

Click into helicorder plot (shows last 24h of data in 30 min segments) to see detailed waveform data, first right click: power spectra, second right click: spectrogram

Shut down from web front-end, never just pull plug (system >> shutdown)

Note: If there are more than one Raspberry Shake on same network, they will appear as rs.local, rs-2.local, …, rs-n.local.

Working Raspberry Shake lights ensemble

Pi board (red (solid), green (flashing every 2-5 s)

Shake board (blue (solid))

Ethernet port (green (flashing repeatedly), orange (solid))

More detailed information:

https://manual.raspberryshake.org/quickstart.html

https://manual.raspberryshake.org/traces.html

for offline application: https://manual.raspberryshake.org/no-network.html

for GPS commands: https://manual.raspberryshake.org/ntp.html#ntptiming

Data download

open rs.local >> Actions icon >> DOWNLOADS >> DATA, opens FTP connection for individual file download

/opt/data/archive/2020/AM/R640E/EHZ.D

Labels

AM.R640E.00 – Shake 1D + Boom

AM.RABE8.00 – Shake 1D + Boom

AM.RC24D.00 – Shake 1D + Boom

AM.RBB35.00 – 3D Shake


Notes

Note: 3Ds will need aligning to true North

Useful terminal commands

ls –lh: check if it records

date: to check UTC date

rsh: shut down

ip n: shows ip addresses

ssh myshake@172.16.1.136 (if this does not work try ssh myshake@rs.local)


GPS software modificaitons

change /etc/default/gpsd to look like this:

START_DAEMON="true" GPSD_OPTIONS="-b -n -G" DEVICES="/dev/ttyUSB0" USBAUTO="true" GPSD_SOCKET="/var/run/gpsd.sock"

change /etc/ntp.conf only this section:

  # GPS Serial data reference                           
  server 127.127.28.0 iburst minpoll 4 maxpoll 4      
  fudge 127.127.28.0 time1 0.500 refid GPS            

check GPS reception: cgps check ntp time sync status: ntpq -p