Difference between revisions of "DFNEXT onservatories BIOS configuration"

From DFN Wiki
Jump to: navigation, search
m (add explanatory note)
m (BIOS - LE-37G7)
 
(One intermediate revision by the same user not shown)
Line 17: Line 17:
  
 
1. Enable Diagnostic Splash Screen
 
1. Enable Diagnostic Splash Screen
''Note: prints eg "Hit Del to enter BISO setup"''
+
 
Boot Features -> Diagnostic Splash Screen  [Enabled]
+
''Note: prints eg "Hit Del to enter BIOS setup"''
 +
  Boot Features -> Diagnostic Splash Screen  [Enabled]
  
 
2. SATA configuretion - enable hot swap
 
2. SATA configuretion - enable hot swap
 +
 
''Note: default is Disabled (symptoms if not set - only 2 removable drives recognized - those attached to the add-on mini PCIe SATA card)''
 
''Note: default is Disabled (symptoms if not set - only 2 removable drives recognized - those attached to the add-on mini PCIe SATA card)''
 
  Advanced -> Intel Advanced menu -> PCH-IO Configuration -> SATA Configuration
 
  Advanced -> Intel Advanced menu -> PCH-IO Configuration -> SATA Configuration
Line 29: Line 31:
  
 
3. Set auto wake up from S5 power down (not critical)
 
3. Set auto wake up from S5 power down (not critical)
''note: S5 is power down. This will save the day if the JAT jumper had fallen off - otherwise not effective''
+
 
 +
''Note: S5 is power down. This will save the day if the JAT jumper had fallen off - otherwise not effective''
 
  Advanced -> Intel Advanced menu -> ACPI settings
 
  Advanced -> Intel Advanced menu -> ACPI settings
 
  Wake system from S5 [Enabled]
 
  Wake system from S5 [Enabled]
 
  Wake Up Hour  [8]
 
  Wake Up Hour  [8]
  
4. Disable unused serial ports to suppress error message during boot (not critical, just to suppress an error print in POST boot message)
+
4. Disable unused serial ports to suppress error message during boot (not critical)
 +
 
 +
''Note: just to suppress an error print in POST boot message)''
 
   Advanced -> Intel Advanced menu -> Super IO Chip
 
   Advanced -> Intel Advanced menu -> Super IO Chip
 
   Serial Port 3 [Disable]
 
   Serial Port 3 [Disable]

Latest revision as of 10:48, 15 June 2022

Commell LE-37G single board industrial PC

This type of SBC is used in DFNEXT observatories. DFN observatories specific configuration is described below.

For more details regarding the Commell LE-37G single board industrial computer please refer to user manual on the manufacturer's web site [1].

Standard HW jumpers setup - LE-37G7

JAT: AT/ATX mode select jumper: switch to AT instead of ATX mode
1-2  AT mode
2-3  ATX mode (Default)
JMSATA: Setting MINI_CARD2 to support PCIe/mSATA: select Support mSATA instead of default
1-2  Support mSATA
2-3  Normal operation (Default)

BIOS - LE-37G7

1. Enable Diagnostic Splash Screen

Note: prints eg "Hit Del to enter BIOS setup"

 Boot Features -> Diagnostic Splash Screen  [Enabled]

2. SATA configuretion - enable hot swap

Note: default is Disabled (symptoms if not set - only 2 removable drives recognized - those attached to the add-on mini PCIe SATA card)

Advanced -> Intel Advanced menu -> PCH-IO Configuration -> SATA Configuration
Serial ATA port 1 - Hot plug - set to  [Enabled]
Serial ATA port 2 - Hot plug - set to  [Enabled]
Serial ATA port 3 - Hot plug - set to  [Enabled]
Serial ATA port 4 - Hot plug - set to  [Enabled]

3. Set auto wake up from S5 power down (not critical)

Note: S5 is power down. This will save the day if the JAT jumper had fallen off - otherwise not effective

Advanced -> Intel Advanced menu -> ACPI settings
Wake system from S5 [Enabled]
Wake Up Hour  [8]

4. Disable unused serial ports to suppress error message during boot (not critical)

Note: just to suppress an error print in POST boot message)

 Advanced -> Intel Advanced menu -> Super IO Chip
 Serial Port 3 [Disable]
 Serial Port 4 [Disable]
 Serial Port 5 [Disable]
 Serial Port 6 [Disable]

5. Save and exit

Exit -> Exit Saving changes