Difference between revisions of "DFNSMALL observatories BIOS configuration"

From DFN Wiki
Jump to: navigation, search
(Created page with "'''Valid for Commell LE-37E PC only!''' === Standard HW jumpers setup - LE-37D === In case of mSATA system SSD disk used - HW jumper JMSATA - must be in position 1-2 (default...")
 
(BIOS - LE-37D, both DFNSMALL and DFNKIT cameras)
 
(14 intermediate revisions by the same user not shown)
Line 1: Line 1:
'''Valid for Commell LE-37E PC only!'''
+
== Commell LE-37D single board industrial PC ==
  
=== Standard HW jumpers setup - LE-37D ===
+
This type of SBC is used in later DFNSMALL and all DFNKIT observatories. DFN observatories specific configuration is described below.
In case of mSATA system SSD disk used
+
 
 +
For more details regarding the Commell LE-37D single board industrial computer please refer to user manual on the manufacturer's web site
 +
[http://www.commell.com.tw/Support/Product%20Technical%20Support/LE-37D.htm].
 +
 
 +
=== Standard HW jumpers setup - LE-37D, DFNKIT cameras ===
 +
In case of mSATA system SSD disk (mini card) used<br>
 
- HW jumper JMSATA - must be in position 1-2 (default is 2-3)
 
- HW jumper JMSATA - must be in position 1-2 (default is 2-3)
- cannot be used simultaneously with CFAST slotj
 
  
=== BIOS - LE-37D ===
+
=== BIOS - LE-37D, both DFNSMALL and DFNKIT cameras ===
  
 
1. PC behaviour after power resume
 
1. PC behaviour after power resume
BIOS -> Others-> Super IO Configuration -> PowerLoss -> Power control [Always ON]
+
BIOS -> Others-> Super IO Configuration -> PowerLoss -> Power control [Always ON]
  
 
2. SATA
 
2. SATA
BIOS -> Advanced -> South cluster configuration -> SATA Drives- select AHCI mode  
+
BIOS -> Advanced -> South cluster configuration -> SATA Drives - select AHCI mode (This is default setting)
  
3. USB3  
+
3. USB3 <br>
There is one USB3 port and 5 USB2 ports, by default USB3 port is extended power only, but USB2 protocol/link speed
+
There is one USB3 port and 5 USB2 ports, by default USB3 port is extended power only, but USB2 protocol/link speed.
 
To enable USB3:
 
To enable USB3:
BIOS -> Advanced -> South cluster configuration -> USB - disable EHCI nmode, enable xHCI mode
+
BIOS -> Advanced -> South cluster configuration -> USB - disable EHCI nmode, enable xHCI mode
 +
 
 +
4. SIM card slot - only for use with mPCIe mobile data 3G/4G modem, otherwise can be left on defaults
 +
BIOS -> Advanced -> South cluster configuration -> Miscelaneous - WLAN card presence - UHPAM card inserted -> ENABLE
 +
 
 +
5. RTC alarm every day wake up (effective only in case of accidentally suspended/hibernated, not when powered down or failed to boot)
 +
BIOS -> Others -> APM Configuration ... Enabled, Everyday, 08:00 (HW clock is in UTC)
  
4. SIM card slot - only for use with mPCIe 3G modem
+
6. Watchdog timer
BIOS -> Advanced -> South cluster configuration -> Miscelaneous - WLAN card presence - UHPAM card inserted -> ENABLE
+
BIOS -> Others-> Super IO Configuration -> Watch dog timer -> Watch dog timer select -> disable (This is default setting)
  
5. RTC alarmevery day wake up
+
''Note: disable Watchdog in BIOS temporarily when cloning system''
Others -> APM Configuration ... Enabled, Everyday, 08:00 (HW clock is in UTC)
 
  
6. Save and exit
+
7. Save and exit
 
  Exit -> Exit Saving changes
 
  Exit -> Exit Saving changes

Latest revision as of 08:12, 30 August 2021

Commell LE-37D single board industrial PC

This type of SBC is used in later DFNSMALL and all DFNKIT observatories. DFN observatories specific configuration is described below.

For more details regarding the Commell LE-37D single board industrial computer please refer to user manual on the manufacturer's web site [1].

Standard HW jumpers setup - LE-37D, DFNKIT cameras

In case of mSATA system SSD disk (mini card) used
- HW jumper JMSATA - must be in position 1-2 (default is 2-3)

BIOS - LE-37D, both DFNSMALL and DFNKIT cameras

1. PC behaviour after power resume

BIOS -> Others-> Super IO Configuration -> PowerLoss -> Power control [Always ON]

2. SATA

BIOS -> Advanced -> South cluster configuration -> SATA Drives - select AHCI mode (This is default setting)

3. USB3
There is one USB3 port and 5 USB2 ports, by default USB3 port is extended power only, but USB2 protocol/link speed. To enable USB3:

BIOS -> Advanced -> South cluster configuration -> USB - disable EHCI nmode, enable xHCI mode

4. SIM card slot - only for use with mPCIe mobile data 3G/4G modem, otherwise can be left on defaults

BIOS -> Advanced -> South cluster configuration -> Miscelaneous	- WLAN card presence - UHPAM card inserted -> ENABLE

5. RTC alarm every day wake up (effective only in case of accidentally suspended/hibernated, not when powered down or failed to boot)

BIOS -> Others -> APM Configuration ... Enabled, Everyday, 08:00 (HW clock is in UTC)

6. Watchdog timer

BIOS -> Others-> Super IO Configuration -> Watch dog timer -> Watch dog timer select -> disable (This is default setting)

Note: disable Watchdog in BIOS temporarily when cloning system

7. Save and exit

Exit -> Exit Saving changes