Difference between revisions of "Mobile network configuration"
Martin Cupak (talk | contribs) m |
Martin Cupak (talk | contribs) m |
||
| Line 33: | Line 33: | ||
Please contact your service provider for details like AP name (here "telstra.m2m"), Password, Username and Phone (number) to dial. The "Modem" field is a virtual port - this parameter is specific for a modem type. | Please contact your service provider for details like AP name (here "telstra.m2m"), Password, Username and Phone (number) to dial. The "Modem" field is a virtual port - this parameter is specific for a modem type. | ||
If you are using the modem MC7455 (for the Americas, Europe, the Middle East and Africa), we believe that it can use the same configuration as MC7430 (for Australia, Asia and Oceania). The only lines that need to be changed are AP name (here "telstra.m2m"), Password, Username and Phone (number) to dial. | If you are using the modem MC7455 (for the Americas, Europe, the Middle East and Africa), we believe that it can use the same configuration as MC7430 (for Australia, Asia and Oceania). The only lines that need to be changed are AP name (here "telstra.m2m"), Password, Username and Phone (number) to dial. | ||
| − | If your service provider does not have specific requirement for Password, Username and Phone (number) to dial, just leave | + | If your service provider does not have specific requirement for Password, Username and Phone (number) to dial or if not sure, just leave these fields as they are (guest, guest, *99#) - please refer to the telstra_sierra_MC8705 example above. |
For both MC7430 and MC7455 you would need to add another section to /etc/wvdial.conf, copying some existing one, give it a unique name and modify those lines: | For both MC7430 and MC7455 you would need to add another section to /etc/wvdial.conf, copying some existing one, give it a unique name and modify those lines: | ||
Revision as of 14:35, 6 November 2019
This page describes the configuration of mobile network in DFN camera systems. For modem module installation in DFNEXT observatories with blue PCB modem adaptor board please refer to DFNEXT Modem Installation.
There are sevaral modem/operator combinations pre-defined in the DFN observatory operating system. These are those we use in Australia. For use with other operators or overseas, a specific configuration needs to be added.
Here is example configuration - please note the bold part of the text - that is identifier of the specific modem/operator setup, that need to match in both configuration files.
For Sierra MC8705 3G modem with Telstra M2M plan is the configuration as shown on a corresponding section of file /etc/network/interfaces.
### Optus/Telstra mobile data GSM/3G/4G ### with modem/ppp interface ### primary network interface in the field, default route auto ppp0 allow-hotplug ppp0 iface ppp0 inet wvdial #provider optus_multitech #provider optus_sierra_MC8705 #provider telstra_multitech provider telstra_sierra_MC8705 #provider telstra_sierra_MC7430
Please notice the uncommented line with provider telstra_sierra_MC8705. All lines with "#" at the beginning are comments.
There are a few more configurations pre-set in file /etc/wvdial.conf. The corresponding detailed section for our case looks like:
[Dialer telstra_sierra_MC8705] Stupid Mode = 1 Init3 = AT+CGDCONT=1,"IP","telstra.m2m" Modem = /dev/ttyUSB0 Password = guest Username = guest Phone = *99#
Please contact your service provider for details like AP name (here "telstra.m2m"), Password, Username and Phone (number) to dial. The "Modem" field is a virtual port - this parameter is specific for a modem type. If you are using the modem MC7455 (for the Americas, Europe, the Middle East and Africa), we believe that it can use the same configuration as MC7430 (for Australia, Asia and Oceania). The only lines that need to be changed are AP name (here "telstra.m2m"), Password, Username and Phone (number) to dial. If your service provider does not have specific requirement for Password, Username and Phone (number) to dial or if not sure, just leave these fields as they are (guest, guest, *99#) - please refer to the telstra_sierra_MC8705 example above. For both MC7430 and MC7455 you would need to add another section to /etc/wvdial.conf, copying some existing one, give it a unique name and modify those lines:
[Dialer YOUR_OPERATOR_sierra_MC7455] Stupid Mode = 1 Init3 = AT+CGDCONT=1,"IP","AP_NAME" Modem = /dev/ttyUSB2 Password = YOUR_PASSWORD Username = YOUR_USERNAME Phone = YOUR_PROVIDER_DIALUP_PHONE_NUMBER
and then you open /etc/network/interfaces, comment out all the 'provider' lines and add your one:
### Optus/Telstra mobile data GSM/3G/4G ### with modem/ppp interface ### primary network interface in the field, default route auto ppp0 allow-hotplug ppp0 iface ppp0 inet wvdial #provider optus_multitech #provider optus_sierra_MC8705 #provider telstra_multitech #provider telstra_sierra_MC8705 #provider telstra_sierra_MC7430 provider YOUR_OPERATOR_sierra_MC7455
