Difference between revisions of "DFNEXT onservatories BIOS configuration"
Martin Cupak (talk | contribs) (added page on DFNEXT Commell LE-37G BIOS configuration) |
Martin Cupak (talk | contribs) m (→BIOS - LE-37G7) |
||
| (7 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
| − | + | == Commell LE-37G single board industrial PC == | |
| + | |||
| + | This type of SBC is used in DFNEXT observatories. DFN observatories specific configuration is described below. | ||
| + | |||
| + | For more details regarding the Commell LE-37G single board industrial computer please refer to user manual on the manufacturer's web site [http://www.commell.com.tw/Support/Product%20Technical%20Support/LE-37G.htm]. | ||
=== Standard HW jumpers setup - LE-37G7 === | === Standard HW jumpers setup - LE-37G7 === | ||
JAT: AT/ATX mode select jumper: switch to AT instead of ATX mode | JAT: AT/ATX mode select jumper: switch to AT instead of ATX mode | ||
| − | 1-2 AT mode | + | '''1-2 AT mode''' |
2-3 ATX mode (Default) | 2-3 ATX mode (Default) | ||
| + | |||
| + | JMSATA: Setting MINI_CARD2 to support PCIe/mSATA: select Support mSATA instead of default | ||
| + | '''1-2 Support mSATA''' | ||
| + | 2-3 Normal operation (Default) | ||
=== BIOS - LE-37G7 === | === BIOS - LE-37G7 === | ||
1. Enable Diagnostic Splash Screen | 1. Enable Diagnostic Splash Screen | ||
| − | ''Note: prints eg "Hit Del to enter | + | |
| − | + | ''Note: prints eg "Hit Del to enter BIOS setup"'' | |
| + | Boot Features -> Diagnostic Splash Screen [Enabled] | ||
2. SATA configuretion - enable hot swap | 2. SATA configuretion - enable hot swap | ||
| + | |||
''Note: default is Disabled (symptoms if not set - only 2 removable drives recognized - those attached to the add-on mini PCIe SATA card)'' | ''Note: default is Disabled (symptoms if not set - only 2 removable drives recognized - those attached to the add-on mini PCIe SATA card)'' | ||
Advanced -> Intel Advanced menu -> PCH-IO Configuration -> SATA Configuration | Advanced -> Intel Advanced menu -> PCH-IO Configuration -> SATA Configuration | ||
| Line 20: | Line 30: | ||
Serial ATA port 4 - Hot plug - set to [Enabled] | Serial ATA port 4 - Hot plug - set to [Enabled] | ||
| − | 3. Set auto wake up from S5 power down | + | 3. Set auto wake up from S5 power down (not critical) |
| − | '' | + | |
| + | ''Note: S5 is power down. This will save the day if the JAT jumper had fallen off - otherwise not effective'' | ||
Advanced -> Intel Advanced menu -> ACPI settings | Advanced -> Intel Advanced menu -> ACPI settings | ||
Wake system from S5 [Enabled] | Wake system from S5 [Enabled] | ||
Wake Up Hour [8] | Wake Up Hour [8] | ||
| − | 4. | + | 4. Disable unused serial ports to suppress error message during boot (not critical) |
| + | |||
| + | ''Note: just to suppress an error print in POST boot message)'' | ||
| + | Advanced -> Intel Advanced menu -> Super IO Chip | ||
| + | Serial Port 3 [Disable] | ||
| + | Serial Port 4 [Disable] | ||
| + | Serial Port 5 [Disable] | ||
| + | Serial Port 6 [Disable] | ||
| + | |||
| + | 5. Save and exit | ||
Exit -> Exit Saving changes | Exit -> Exit Saving changes | ||
Latest revision as of 10:48, 15 June 2022
Commell LE-37G single board industrial PC
This type of SBC is used in DFNEXT observatories. DFN observatories specific configuration is described below.
For more details regarding the Commell LE-37G single board industrial computer please refer to user manual on the manufacturer's web site [1].
Standard HW jumpers setup - LE-37G7
JAT: AT/ATX mode select jumper: switch to AT instead of ATX mode 1-2 AT mode 2-3 ATX mode (Default)
JMSATA: Setting MINI_CARD2 to support PCIe/mSATA: select Support mSATA instead of default 1-2 Support mSATA 2-3 Normal operation (Default)
BIOS - LE-37G7
1. Enable Diagnostic Splash Screen
Note: prints eg "Hit Del to enter BIOS setup"
Boot Features -> Diagnostic Splash Screen [Enabled]
2. SATA configuretion - enable hot swap
Note: default is Disabled (symptoms if not set - only 2 removable drives recognized - those attached to the add-on mini PCIe SATA card)
Advanced -> Intel Advanced menu -> PCH-IO Configuration -> SATA Configuration Serial ATA port 1 - Hot plug - set to [Enabled] Serial ATA port 2 - Hot plug - set to [Enabled] Serial ATA port 3 - Hot plug - set to [Enabled] Serial ATA port 4 - Hot plug - set to [Enabled]
3. Set auto wake up from S5 power down (not critical)
Note: S5 is power down. This will save the day if the JAT jumper had fallen off - otherwise not effective
Advanced -> Intel Advanced menu -> ACPI settings Wake system from S5 [Enabled] Wake Up Hour [8]
4. Disable unused serial ports to suppress error message during boot (not critical)
Note: just to suppress an error print in POST boot message)
Advanced -> Intel Advanced menu -> Super IO Chip Serial Port 3 [Disable] Serial Port 4 [Disable] Serial Port 5 [Disable] Serial Port 6 [Disable]
5. Save and exit
Exit -> Exit Saving changes
